Precor Cycle 842i Manual de Serviço

Service Bulletin — 0303.1Consumer EFX Drive UnitsAbout this Troubleshooting DocumentThis document lists the error codes that exist within the Precor s

Error 20 - Too many Maximum Power Requests in 1 SecondDescriptionThis error monitors the treadmills power bit reading when the treadmill was operating

Error 21 - Too many Maximum Consecutive Power RequestsDescriptionThis error monitors the treadmills power bit reading when the treadmill was operating

Error 22 - No Motor Pulses at Start UpDescriptionError 22 indicates that the drive motor (running belt) has been instructed to start, by either manual

Error 23 - Motor Pulses Missing after Start UpDescriptionError 23 indicates that the speed sensor signal was lost while the treadmill was in operation

Error 24 - Reduce Speed Requested, Speed is not ReducingDescriptionError 24 indicates that the the speed control system has instructed the treadmill t

Error 25 - Motor Pulse Count over Acceptable LimitDescriptionThis error monitors the treadmills power bit reading. Power bits indicate the relative ti

Error 26 - Motor Pulse Width IncorrectDescriptionThis error monitors the speed sensor signal and verifies the the speed sensor signal is appropriate f

Error 27 - Too Much Drive Motor CurrentDescriptionSome treadmill motor controllers monitor the amount of current being delivered to the drive motor. T

Error 28 - Temperature Too HighDescriptionSome treadmill motor controllers monitor the temperature of the motor controller output switching device. Ty

Error 30, 31, 32 and 33 - Communications ErrorDescriptionErrors 30 through 33 all indicate the loss of communications or erratic communications betwee

Error 00, 01, 02, 03, 04 - Memory, Ram & EEPROM Test ErrorsDescriptionErrors 00 through Error 04 check upper PCA memory locations, RAM memory loca

Error 40 - No Lift Motion DetectedDescriptionError indicates that the incline (lift) system on either a treadmill or EFX has been instructed to start

Error 41 - Lift has not Responded in Acceptable TimeDescriptionThis error code was present in early versions of software and is no longer being used.

Error 42 - Lift Position Value Out of RangeDescriptionThis error code monitors the physical lift position via a lift position potentiometer that mecha

Error 43 - Zero Switch not FoundDescriptionThe C944 and several versions of C96X used a lift position identification system that did not utilize a pot

Error 44 - Un-commanded Lift MotionDescriptionThe lift control system has detected that the lift is in motion without a lift command having been issue

Error 45 - Lift Moving in Wrong DirectionDescriptionThe lift control system has detected that the lift is moving in the opposite direction of the issu

Error 50 - Too Much Brake (Magnet) CurrentDescriptionThis error is associated with eddy current EFX’s. The resistance (brake) control system constantl

Error 53 - Can’t Read Target, Can’t Find Home SwitchDescriptionThis error is associated with the 5.17 EFX. When power is first applied to the 5.17, an

Error 54 - Target Pulses Lost During OperationDescriptionThis error is associated with the 5.17 EFX. This error indicates that at some time after the

Error 55 - Brake Home Switch Activated UnexpectedlyDescriptionThis error is associated with the 5.17 EFX. This error indicates that the home switch wa

Error 05 - Key Depressed at Power UpDescriptionThe power up test sequence has detected a key in the operated condition. The power up test sequence is

Error 09 - Lower PCA Memory Test ErrorsDescriptionError 09 checks lower PCA memory locations during the power up test sequence. If a fault is found du

Error 10 - Line Frequency out of Acceptable RangeDescriptionThis error is present on treadmills using an SCR motor controller and the C544 EFX. Becaus

may be replacing the treadmill with a treadmill utilizing a PWM motor controller. PWM motor controllers do not depend on line frequency for speed cont

Error 11 - Watchdog (Upper PCA)DescriptionThe error 11 watchdog monitors the upper PCA low voltage power. If the low voltage power drops below a pres

Error 12 - Watchdog (Lower PCA)DescriptionThe error 12 watchdog monitors the lower PCA low voltage power. If the low voltage power drops below a pres

Error 13 - Fan at Incorrect SpeedDescriptionThis error monitored the rotating speed of an external cooling fan attached to the drive motor on 9.55, C