Precor Strength-Training S3.25 Manual do Utilizador

Assembly and Maintenance GuideS3.25Strength-TrainingFitness Equipment

S3.25 Assembly and Maintenance Guidepage 101 2 3 4 5 62. Attach Chest Press BaseA. Attach the Chest Press Base to the Main Uprightusingone 3¼-inch bol

S3.25 Assembly and Maintenance Guidepage 111 2 3 4 5 6Open Box 2Use tie cutters to open the box.The illustration shows how the S3.25 will look after y

S3.25 Assembly and Maintenance Guidepage 121 2 3 4 5 63. Assemble Leg Curl SeatExtensionA. Use a flathead screwdriver to remove the blackend cap on th

S3.25 Assembly and Maintenance Guidepage 131 2 3 4 5 64. Attach Rotating Arm andHandlesA. Attach the Rotating Arm to the Upright Flats usingtwo ¾-inch

S3.25 Assembly and Maintenance Guidepage 141 2 3 4 5 65. Attach Roller PadsA. Insert the Leg Curl Roller Pad Rod.B. Slide the Leg Curl Roller Pads on

S3.25 Assembly and Maintenance Guidepage 151 2 3 4 5 66. Assemble Leg Curl SeatA. Attach the Backpad Support Tubes to the SeatUpright usingone 5½-inch

S3.25 Assembly and Maintenance Guidepage 161 2 3 4 5 6D. Attach the lower section of the Backpad to thelower hole of the right Backpad Support Tube us

S3.25 Assembly and Maintenance Guidepage 171 2 3 4 5 6Open Box 3Use tie cutters to open the box.The diagram shows how the S3.25 will look after youcom

S3.25 Assembly and Maintenance Guidepage 181 2 3 4 5 67. Assemble Chest Press SeatA. Attach the Chest Press Upright to the Chest PressSeat usingfour ¾

S3.25 Assembly and Maintenance Guidepage 191 2 3 4 5 68. Attach Press Arm AssemblyCAUTION: This step requires two people. Do notpinch yourself between

S3.25 Assembly and Maintenance Guidepage 2IMPORTANT SAFETY INSTRUCTIONSImportant Safety InstructionsImportant Safety InstructionsBefore beginning any

S3.25 Assembly and Maintenance Guidepage 201 2 3 4 5 69. Attach HandlebarsA. Slide each Handlebar (one at a time) on the PivotShaft.B. To the end of e

S3.25 Assembly and Maintenance Guidepage 211 2 3 4 5 610. Assemble Chest Press SeatA. Place the Backpad and Headrest on the floor. Placethe Long Suppo

S3.25 Assembly and Maintenance Guidepage 221 2 3 4 5 6Open Box 4Use tie cutters to open the box.The diagram shows how the S3.25 will look after youcom

S3.25 Assembly and Maintenance Guidepage 231 2 3 4 5 611. Assemble Weight StackImportant: Position your unit in its permanent locationbefore assemblin

S3.25 Assembly and Maintenance Guidepage 241 2 3 4 5 612. Feed Upper CableA. Attach a 4½-inch pulley to the top of the MainUpright usingone 4¼-inch bo

S3.25 Assembly and Maintenance Guidepage 251 2 3 4 5 6G. Insert the Selector Stem in the Weight Stack withthe threaded hole at the top. Hold the Selec

S3.25 Assembly and Maintenance Guidepage 261 2 3 4 5 613. Attach Lat Bar HoldersA. Attach the Lat Bar Holders to the Top Beam usingtwo 3¼-inch boltsfo

S3.25 Assembly and Maintenance Guidepage 271 2 3 4 5 614. Feed Cable From Cable TreeA. Feed the Spring Clip end of Cable 44371-103 undera 4½-inch pull

S3.25 Assembly and Maintenance Guidepage 281 2 3 4 5 6E. In the middle hole on the Press Arm Flats, make aretainer pin usingone 2-inch bolttwo washers

S3.25 Assembly and Maintenance Guidepage 291 2 3 4 5 615. Attach Leg Curl Cables toLower Pulley BracketA. Wrap Cable 44376-102 around a 3½-inch pulley

S3.25 Assembly and Maintenance Guidepage 3Table of ContentsTable of Contents123Important Safety Instructions ...

S3.25 Assembly and Maintenance Guidepage 301 2 3 4 5 616. Attach Leg Curl Cables toSeat UprightA. Attach the Pulley Cover to the Main Upright Baseusin

S3.25 Assembly and Maintenance Guidepage 311 2 3 4 5 617. Feed Top Cable 44376-102A. Attach Cable 44376-102 to the Rotating Arm usingone 2¾-inch boltt

S3.25 Assembly and Maintenance Guidepage 321 2 3 4 5 618. Feed Bottom Cable44375-103A. Feed Cable 44375-103 through the Upright Flats,through the Seat

S3.25 Assembly and Maintenance Guidepage 331 2 3 4 5 619. Attach Surgical Tubing toTop BeamA. Attach the other end of the surgical tubing to theTop Be

S3.25 Assembly and Maintenance Guidepage 341 2 3 4 5 620. Attach Leg Curl Cables toCable TreeA. Remove the U end of Cable 44376-102. Insert theCable

S3.25 Assembly and Maintenance Guidepage 351 2 3 4 5 621. Attach AccessoriesA. Attach the Lat Bar to the Spring Clip at the end ofthe Top Beam.B. Atta

S3.25 Assembly and Maintenance Guidepage 361 2 3 4 5 622. Attach ShroudsImportant: Before attaching the Shrouds, make anynecessary adjustments. Refer

S3.25 Assembly and Maintenance Guidepage 371 2 3 4 5 64Adjustments andMaintenanceAfter the S3.25 is completely assembled, you mustcheck the Cables for

S3.25 Assembly and Maintenance Guidepage 381 2 3 4 5 62. Selector Stem AdjustmentsTo prevent the Selector Stem from contacting the insideof the Weight

S3.25 Assembly and Maintenance Guidepage 391 2 3 4 5 6D. Reassemble the Cap Plate, Selector Stem, andCable Clamp.E. Test the movement of the Selector

S3.25 Assembly and Maintenance Guidepage 4Table of ContentsOpen Box 4 ...

S3.25 Assembly and Maintenance Guidepage 401 2 3 4 5 6Side-to-Side Vertical AdjustmentIf the Selector Stem contacts the inside of the WeightStack duri

page 41RET.To allow us to serve you better, please take a few moments tocomplete and return your warranty registration.YOU MAY ALSO REGISTER ONLINE AT

page 42 TELL US ABOUT YOUR NEW PRECOR PRODUCTPurchasedfrom:The serial number is located on the shipping box and on the product.ProductSerialNumber:Ple

Effective 01 January 2003P/N 36287-110Precor Residential Equipment Limited WarrantyPLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE US

S3.25 SpecificationsLength: 66 inches (168 cm)Height: 82 inches (208 cm)Width: 48 inches (122 cm) Leg press option adds 15 inches (38 cm)Shipping w

S3.25 Assembly and Maintenance Guidepage 51Before You BeginBefore You BeginThank you for purchasing the S3.25. This unit is partof the Pacific Fitness

S3.25 Assembly and Maintenance Guidepage 62PreparationsPreparationsCAUTION: To set up this unit, you will needassistance. Do not attempt assembly by y

S3.25 Assembly and Maintenance Guidepage 71 2 3 4 5 63AssemblyInstructionsAssembly InstructionsAssembly of the S3.25 takes professional installersabou

S3.25 Assembly and Maintenance Guidepage 81 2 3 4 5 6Open Box 1Open Box 1Use tie cutters to open the box.The illustration shows how the S3.25 will loo

S3.25 Assembly and Maintenance Guidepage 91 2 3 4 5 6Step 1. Attach Rear Upright to Main Upright1. Attach Rear Upright toMain UprightBegin the assembl